[2026] 300-110 Actual Exam Dumps, 300-110 Practice Test [Q11-Q35]

QUESTION 11
A customer purchases this Cisco equipment for a new branch office: ?20 Cisco Catalyst 9120 APs ?five Catalyst 9130 APs ?a single Catalyst 9300 Series Switch The customer wants to extend its existing wired and wireless fabric-enabled network to the branch office and manage all devices via a centrally deployed Cisco Catalyst Center (formerly DNA Center). Which Cisco Catalyst Center licenses are required for the branch office equipment?

Cisco Catalyst Advantage for the switch and all the APs

Cisco Catalyst Essentials on the APs and Cisco Catalyst Advantage on the switch

Cisco Catalyst Essentials on the switch and all the APs

Cisco Catalyst Advantage on the APs and Cisco Catalyst Center Premiere on the switch

QUESTION 12
A consultant must design a WLAN for a large campus with high AP density, 50-100 clients per cell, 5 Mbps throughput per client minimum, 5 GHz and 2.4 GHz coverage at -67 dBm, and no 802.11b clients. Which two WLAN design approaches meet the requirements? (Choose two.)

Set the minimum mandatory data rates to 12-18 Mbps.

Configure up to six SSIDs on any AP.

Enable 802.11b data rates.

Reduce the 2.4 GHz coverage with FRA.

Set the 5 GHz channel widths to 80-160 MHz.

QUESTION 13
A customer has an existing wireless network with a Cisco 9800 WLC high availability cluster and Cisco 9120 APs. The customer asks an engineer to perform a post wireless survey that includes a list of any non-802.11 devices on the 5 GHz band. The engineer performs the survey using an 802.11a/b/g/n/ac/ax WLAN adapter but did not use a spectrum analyzer. Which approach meets the requirements?

Export a list of 802.11b interferers using the WLC and the RF ASIC embedded in the APs.

Set the WLAN adapter to monitor mode and perform the analysis by using 802.11b.

Set the WLAN adapter to monitor mode and perform the analysis by using 802.11a.

Export a list of 802.11a interferers using the WLC and the RF ASIC embedded in the APs.

QUESTION 14
A customer has two Cisco WLCs configured in a SSO cluster. The wireless network supports a large warehouse. The customer purchases new iPads to replace legacy scanners. Both devices connect to a single SSID named Scanning by using WPA2 Personal. The customer wants to use a standards-based method for fast roaming on the new iPads. Which approach meets the scanner requirement and still supports the legacy scanners?

Enable FT 802.1X and set Fast Transition to Adaptive for the Scanning SSID.

Enable optimized roaming globally and enable FT 802.1X on the Scanning SSID.

Enable optimized roaming globally and enable FT PSK on the Scanning SSID.

Enable FT PSK and set Fast Transition to Adaptive for the Scanning SSID.

QUESTION 15
A customer is building a new warehouse facility that has only its foundation and perimeter walls built. The building will be complete in the next eight months. The customer needs a detailed bill of materials and costs for a wireless network that must support RF scanners throughout the warehouse.
How should the survey be performed?

Perform a passive survey by simulating the wireless propagation using modeled attenuation areas on a digital floor plan.

Perform a predictive survey of the existing building and simulate the future attenuation objects using a passive survey.

Perform a passive survey of the existing building and simulate the future attenuation objects using a predictive survey.

Perform a predictive survey by simulating the wireless propagation using modeled attenuation areas on a digital floor plan.

QUESTION 16
An engineer must perform a predictive design for a wireless network.
The customer has devices that can tolerate at most 100 ms of delay when roaming. Which design criteria must be used?

location

data

video

voice

QUESTION 17
A university has three campus locations and the main data center. Each campus location has a Cisco Catalyst
9800-40 WLC that manages 600 APs. The data center has a Catalyst 9800-40 WLC, which serves as N+1 backup for each campus WLC. A consulting engineer must install four additional Catalyst 9800-40 WLCs to serve as high availability SSO pairs for each campus, but only two have been approved due to budget restrictions. Requirements: Data center WLC must always be available as N+1 backup, Campus1 WLC must operate with zero downtime, and in the event of multiple campus outages, the AP priority order is to support Campus3, Campus2, then Campus1. Which design approach must the consulting engineer take?

The data center WLC and Campus3 WLC are the high availability SSO pair. Campus1 APs have priority 4, Campus2 APs have priority 2, and Campus3 APs have priority 1.

The data center WLC and Campus1 WLC are the high availability SSO pair. Campus1 APs have priority 4, Campus2 APs have priority 2, and Campus3 APs have priority 1.

The data center WLC and Campus1 WLC are the high availability SSO pair. Campus3 APs have priority 4, Campus2 APs have priority 2, and Campus1 APs have priority 1.

The data center WLC and Campus3 WLC are the high availability SSO pair. Campus3 APs have priority 4, Campus2 APs have priority 2, and Campus1 APs have priority 1.

QUESTION 18
Which issue occurs when wireless access points transmit by using the highest power level in a building that has brick walls?

hidden node

wideband interference

reflection

narrowband interference

QUESTION 19
During a post-deployment site survey, issues are found with non-Wi-Fi interference. What should the engineer use to identify the source of the interference?

Network analysis module

Wireless intrusion prevention

Wireshark

Cisco spectrum expert

QUESTION 20
An enterprise is using two wireless controllers to support the wireless network. The data centre is located in the head office. Each controller has a corporate WLAN configured with different SSID names. The APs are installed using a round-robin approach to load balance the traffic. What should be changed in the configuration to optimize roaming?

Move all access points to one controller and use the other as N+1 HA.

Use the same WLAN name for the corporate network on both controllers.

Place the access points per floor on the same controller.

QUESTION 21
A wireless engineer must design a backhaul link. The engineer has a mesh access point that has a wired connection back to the infrastructure. What must be changed in the AP role before a change is made in the AP mode?

monitor

RAP

bridge

local

QUESTION 22
The wireless team must configure a new voice SSID for optimized roaming across multiple WLCs with Cisco
8821 phones. Which two settings accomplish this goal? (Choose two.)

Configure mobility groups between WLCs.

Use Cisco Centralized Key Management for authentication.

Configure AP groups between WLCs.

Configure AVC profile on new SSID.

Use AVC to tag traffic voice traffic as best effort.

QUESTION 23
An engineer is designing a wireless network for a facility located 3 km from an airport with a terminal Doppler weather radar installation. Which design consideration applies to the 5 GHz channel plan?

DFS channels must be statically assigned to prevent channel changes.

APs on DFS channels may vacate the channel when radar is detected, causing a brief service interruption.

DFS channels provide higher transmit power and should be prioritized for client-serving radios.

Radar detection applies only to the UNII-1 band.

QUESTION 24
A customer wants to provide wireless coverage in a parking lot outside of a building. An engineer determines that three APs are required. The APs can be mounted on the light poles in the parking lot because there are cable routes already in place for these locations. The closest wiring closet is approximately 200 meters away. Which setup powers and connects the APs back to the customer network?

category 6 UTP cabling and Cisco UPOE

fiber connectivity with 802.3af

fiber connectivity with an AC/DC power module

Category 6 UTP cabling and PoE+

QUESTION 25
A customer purchases this Cisco equipment for a new branch office: ?20 Cisco Catalyst 9120 APs ?five Catalyst 9130 APs ?a single Catalyst 9300 Series Switch The customer wants to extend its existing wired and wireless fabric-enabled network to the branch office and manage all devices via a centrally deployed Cisco Catalyst Center (formerly DNA Center). Which Cisco Catalyst Center licenses are required for the branch office equipment?

Cisco Catalyst Advantage for the switch and all the APs

Cisco Catalyst Essentials on the APs and Cisco Catalyst Advantage on the switch

Cisco Catalyst Essentials on the switch and all the APs

Cisco Catalyst Advantage on the APs and Cisco Catalyst Center Premiere on the switch

QUESTION 26
A wireless engineer is using Ekahau Site Survey to validate that an existing wireless network is operating as expected. A Cisco CleanAir AP is used for Layer 1 survey by using Metageek Chanalyzer only on the current operating channel. Which operating mode is configured for the Cisco CleanAir AP?

Local

Sniffer

Monitor

SE-connect

QUESTION 27
Which profile is included within a site tag when configured in a Cisco 9800 WLC architecture?

QoS

NAT

Flex

VLAN

QUESTION 28
A community bank has three campus locations and one HQ with the data center. Each campus has four Cisco Catalyst 9120 APs. Poor WAN uplinks cause impacted connectivity back to HQ, and each campus is planned to have its own EWC controller based on C9120 AP to keep traffic local. Guest WLAN will be routed locally.
Employee WLAN must be authenticated 802.1x PEAP via HQ ISE but can pass traffic locally once authenticated. HQ WLC will be the primary backup WLC for each WLC. Which design approach should the consulting engineer take?

One C9120 AP in each campus must be converted to EWC mode, and the preferred controller is set to that AP with HQ WLC set as N+1 backup. The campus guest WLAN will use local web auth on guest VLAN, and employee WLAN will need the HQ AAA server to be added to EWC.

Two C9120 campus APs must be converted to EWC mode, one for the active controller and the other for standby set as N+1 backup. The campus guest WLAN will use local web auth on guest VLAN, and employee WLAN will need the HQ AAA server added to EWC.

Two C9120 campus APs must be converted to EWC mode, one for the active controller and the other for standby with HQ WLC as N+1 backup. The campus guest WLAN will use the guest anchor to HQ WLC for guest VLAN access, and employee WLAN will need the HQ AAA server added to EWC.

One C9120 campus AP must be converted to EWC mode, and the preferred controller is set to that AP with HQ WLC paired as mobility peer and configured as N+1 backup. The campus guest WLAN will use local web auth on guest VLAN. The campus employee WLAN will need the guest anchor back to the HQ employee WLAN.

QUESTION 29
An engineer in a branch office that does not have a wired backhaul must ensure that local clients can be switched locally and authenticated centrally. In which mode must the AP be configured?

MAP

Flex+Bridge

RAP

Cisco FlexConnect

QUESTION 30
A retail customer opened two new branch locations, and the main store HQ handles data center operations. Each branch location has three Cisco Catalyst 9130 APs. The data center has a Catalyst 9800 WLC with 18 Catalyst 9130 APs. Growing business and poor WAN uplinks cause impacted branch AP and wireless client connectivity back to HQ, and each branch location is now planned to have its own EWC controller based on C9130 AP to keep traffic local. This new design must accommodate: guests and employees sharing the same WLAN with different VLANs, guest uplink and downlink traffic restricted to 2 Mbps, and each branch acting as secondary or tertiary backup to another branch with the data center WLC always being the primary. Which design approach should the consulting engineer take?

Two C9130 branch APs must be converted to EWC mode, one for the active controller and the other for standby, with HQ WLC set as a primary N+1 backup, and other branches’ EWC must be added as mobility peers. The branch WLAN will use the guest anchor to HQ WLC for guest VLAN access.

One C9130 branch AP must be converted to EWC mode, and the preferred controller is set to that AP with HQ WLC set as a primary N+1 backup and other branches’ EWC AP as secondary and tertiary. HQ AAA must be added to EWC, and WLAN with MAB + AAA override must be configured.

Two C9130 branch APs must be converted to EWC mode, one for the active controller and the other for standby, with the standby EWC set as N+1 backup. HQ AAA must be added to EWC, and WLAN with dot1x + AAA override must be configured.

One C9130 branch AP must be converted to EWC mode, and the preferred controller is set to that AP with HQ WLC set as N+1 backup. The branch guest WLAN will use local web auth on guest VLAN.

QUESTION 31
A customer wants to provide wireless coverage in a parking lot outside of a building. An engineer determines that three APs are required. The APs can be mounted on the light poles in the parking lot because there are cable routes already in place for these locations. The closest wiring closet is approximately 200 meters away.
Which setup powers and connects the APs back to the customer network?

category 6 UTP cabling and Cisco UPOE

fiber connectivity with 802.3af

fiber connectivity with an AC/DC power module

Category 6 UTP cabling and PoE+

QUESTION 32
A campus has two controllers, each with client VLANs on different subnets. A client associated to an AP on WLC-1 roams to an AP on WLC-2. Which behavior does the mobility design produce, and what is required?

A Layer 2 roam occurs; no mobility configuration is required.

A Layer 3 roam occurs; the client keeps its IP address through an asymmetric tunnel from the anchor to the foreign controller.

A Layer 3 roam occurs; the client must obtain a new IP address from WLC-2.

The client is deauthenticated and must reauthenticate from the beginning.

QUESTION 33
A customer designs a Cisco wireless environment to provide connectivity to employees and guests. The guest SSID must be configured on three anchor WLCs named Anchor1, Anchor2, and Anchor3 in a DMZ. The guest anchor priority must be configured to ensure that Anchor1 has the highest priority. Which priority level must be incorporated in the design for Anchor1?

0

1

2

3

QUESTION 34
An engineer configured the optimized client roaming on Cisco WLC with an RSSI threshold of -72 dBm. Clients report frequent disconnections. What must be configured for the AP to guide the client to a better AP?

Enable BSS transition on the SSID and optimized roaming at the radio level.

Disable coverage hole detection on the SSID and enable BSS transition on the SSID.

Enable BSS transition at the radio level and optimized roaming on the SSID.

Disable optimized roaming and enable 802.11v support on the SSID.

QUESTION 35
Refer to the exhibit. A wireless engineer is using the Ekahau Site Survey tool to conduct a post-deployment survey. The engineer analyzes the pictured output to determine if SNR meets the voice requirements. How is the voice support based on the output?
Exhibit – Q15: Ekahau SNR Heatmap – Post-Deployment Survey Output

It works in the top-middle room.

It is not supported.

It works in the lobby.

It works in all locations.

[2026] 300-110 Actual Exam Dumps, 300-110 Practice Test [Q11-Q35]

Leave a Reply Cancel reply