NEW QUESTION 117
An LTM HTTP pool has an associated monitor that sends a string equal to ‘GET /test.html’.
Which two configurations could an LTM Specialist implement to allow server administrators to disable their pool member servers without logging into the LTM device? (Choose two.)

NEW QUESTION 118
There is a fault with an LTM device load balanced trading application that resides on directly connected VLAN vlan-301. The application virtual server is 10.0.0.1:80 with trading application backend servers on subnet
192.168.0.0/25. The LTM Specialist wants to save a packet capture with complete payload for external analysis.
Which command should the LTM Specialist execute on the LTM device command line interface?

NEW QUESTION 119
An LTM Specialist is troubleshooting an issue with a new virtual server. When connecting through the virtual server, clients receive the message “The connection was reset” in the browser, although connections directly to the pool member show the application is functioning correctly.
ltm pool srv1_https_pool {
members {
192.168.2.1:https{
address 192.168.2.1
}
}
}
ltm virtual https_example_vs {
destination 192.168.1.155:https
ip-protocol tcp
mask 255.255.255.255
pool srv1_https_pool
profiles {
http { }
tcp { }
}
snat automap
vlans-disabled
}
How should the LTM Specialist resolve this issue?

NEW QUESTION 120
What is the correct command to reset an LTM device to its default settings?

NEW QUESTION 121
— Exhibit –

— Exhibit –
Refer to the exhibits.
Users are able to access the application when connecting directly to the web server but are unsuccessful when connecting to the virtual server.
What is the cause of the application access problem?

NEW QUESTION 122
An LTM Specialist needs to modify the logging level for tcpdump execution events. Checking the BigDB Key, the following is currently configured:
sys db log.tcpdump.level {
value “Notice”
}
Which command should the LTM Specialist execute on the LTM device to change the logging level to informational?

NEW QUESTION 123
An LTM device is deployed in a one-armed topology. The virtual server, clients, and web servers are connected on the LTM device internal VLAN. A client tries to connect to the virtual server and is unable to establish a connection. A packet capture from the LTM device internal VLAN shows that the HTTP request is being forwarded to the web server.
From which two additional locations should protocol analyzer data be collected? (Choose two.)

NEW QUESTION 124
— Exhibit- — Exhibit -Refer to the exhibit.

An LTM device is used to load balance web content over a secure channel.
The developers of the web content have done a trace using an HTTP profiler application.
They believe that allowing the LTM device to compress traffic to the client will improve
performance. The client can utilize GZIP or deflate compression algorithms.
An LTM Specialist must implement the compression.
The LTM Specialist has completed the following actions:
1.Create the relevant profile.
2.Apply the relevant profile to the virtual server (VS).
After applying the relevant profile, the LTM device is failing to compress the traffic. Instead,
the traffic is being served with an error.
What is the problem?

NEW QUESTION 125
An LTM Specialist is troubleshooting a problem on an eCommerce website. The user browses the online store using port 80, adding items to the shopping cart. The user then clicks the “Checkout” button on the site, which redirects the user to port 443 for the checkout process. Suddenly, the user’s shopping cart is shown as empty. The shopping cart data is stored in memory on the server, and the default source address persistence profile is used on both virtual servers.
What is the issue?

NEW QUESTION 126
— Exhibit – — Exhibit –


Refer to the exhibits.
Users are able to access the application when connecting to the virtual server but are unsuccessful when connecting directly to the application servers. The LTM Specialist wants to allow direct access to the application servers.
Why are users unable to connect directly to the application servers?

NEW QUESTION 127
— Exhibit –

— Exhibit —
Refer to the exhibit.
An LTM Specialist has uploaded a qkview to F5 iHealth.
Within the GUI, what is the correct procedure to comply with the recommendation shown in the
exhibit?

NEW QUESTION 128
— Exhibit –

— Exhibit —
Refer to the exhibit.
An administrator created a monitor to a pool member web server, which resulted in a pool member that is marked red. The administrator knows the web server is working when it is accessed from another computer.
What should the administrator do to correct the problem?

NEW QUESTION 129
Which command line interface command will check if the BIG-IP platform contains a packet velocity ASIC (PVA)?

NEW QUESTION 130
The LTM device is configured for RADIUS authentication. Remote logins are failing and the LTM Specialist must verify the RADIUS configuration.
How should the LTM Specialist check the RADIUS server and shared secret configured on the LTM device?

NEW QUESTION 131
An LTM Specialist must perform a hot fix installation from the command line.
What is the correct procedure to ensure that the installation is successful?

NEW QUESTION 132
An LTM Specialist has been asked to configure a virtual server to distribute connections between a pool of two application servers with addresses 172.16.20.1 and 172.16.20.2. The application servers are listening on TCP ports 80 and 443. The application administrators have asked that clients be directed to the same node for both HTTP and HTTPS requests within the same session.
Virtual servers vs_http and vs_https have been created, listening on 1.2.3.100:80 and 1.2.3.100:443, respectively.
Which configuration option will result in the desired behavior?

NEW QUESTION 133
An LTM Specialist is tasked with ensuring that the syslogs for the LTM device are sent to a remote syslog server.
The following is an extract from the config file detailing the node and monitor that the LTM device is using for the
remote syslog server:
monitor Syslog_15002 { defaults from udp dest *:15002
}
node 91.223.45.231 { monitor Syslog_15002
screen RemoteSYSLOG }
There seem to be problems communicating with the remote syslog server. However, the pool monitor shows that the remote server is up.
The network department has confirmed that there are no firewall rules or networking issues preventing the LTM device from
communicating with the syslog server. The department responsible for the remote syslog server indicates that there may
be problems with the syslog server. The LTM Specialist checks the BIG-IP LTM logs for errors relating to the remote syslog
server. None are found. The LTM Specialist does a tcpdump:
tcpdump -nn port 15002, with the following results: 21:28:36.395543 IP 192.168.100.100.44772 > 91.223.45.231.15002: UDP, length 19 21:28:36.429073 IP 192.168.100.100.39499 > 91.223.45.231.15002: UDP, length 169 21:28:36.430714 IP 192.168.100.100.39499 > 91.223.45.231.15002: UDP, length 181 21:28:36.840524 IP 192.168.100.100.39499 > 91.223.45.231.15002: UDP, length 169 21:28:36.846547 IP 192.168.100.100.39499 > 91.223.45.231.15002: UDP, length 181 21:28:39.886343 IP 192.168.100.100.39499 > 91.223.45.231.15002: UDP, length 144
NotE. 192.168.100.100 is the self IP of the LTM device.
Why are there no errors for the remote syslog server in the log files?

NEW QUESTION 134
— Exhibit –

— Exhibit —
Refer to the exhibit.
A client attempts to connect from a Google Chrome browser to a virtual server on a BIG-IP LTM. The virtual server is SSL Offloaded. When the client connects, the client receives an SSL error. The client receives the same errors when trying Mozilla Firefox and Internet Explorer browsers.
The LTM Specialist does an ssldump on the virtual server and receives the results as per the exhibit.
How should this be resolved?

NEW QUESTION 135
— Exhibit-


— Exhibit –
Refer to the exhibits.
After upgrading LTM from v10 to v11, users are unable to connect to an application. The virtual server is using a client SSL profile for re-terminating SSL for payload inspection, but a server SSL profile is being used to re-encrypt the request.
A client side ssldump did NOT show any differences between the traffic going directly to the server and the traffic being processed by the LTM device. However, packet capture was done on the server, and differences were noted.
Which modification will allow the LTM device to process the traffic correctly?

NEW QUESTION 136
— Exhibit –

— Exhibit -Refer to the exhibits.
Every monitor has the same Send String, Recv String, and an Alias of *:*. The LTM Specialist simplifies the configuration to minimize the number of monitors.
How many unique monitors remain?

NEW QUESTION 137
The output of a tmsh command is: ———————————————————— Net::Interface Name Status Bits Bits Errs Errs Drops Drops Colli In Out In Out In Out sions
———————————————————— 1.1 down 0 0 0 0 0 0 0 1.2 up 191.4K 0 0 0 374 0 0 1.3 down
0 0 0 0 0 0 0 1.4 up 22.5K 0 0 0 44 0 0 2.1 miss 0 0 0 0 0 0 0 2.2 miss 0 0 0 0 0 0 0 mgmt up 43.2G
160.0G 0 0 0 0 0
Which command was executed on the LTM device to show the output?

NEW QUESTION 138
An LTM Specialist is troubleshooting virtual server 10.0.0.1:443 residing on VLAN vlan301. The web application is accessed via www.example.com. The LTM Specialist wants to save a packet capture with complete decrypted payload for external analysis.
Which command should the LTM Specialist execute on the LTM device command line interface?

NEW QUESTION 139
Which file should be modified to create custom SNMP alerts?