Apr-2024 Free Fortinet NSE7_EFW-7.0 Exam Question Practice Exams [Q48-Q64]

NSE7_EFW-7.0 Fortinet

admin • April 17, 2024

Apr-2024 Free Fortinet NSE7_EFW-7.0 Exam Question Practice Exams [Q48-Q64]

Rate this post

Apr-2024 Free Fortinet NSE7_EFW-7.0 Exam Question Practice Exams

Ace NSE7_EFW-7.0 Certification with 165 Actual Questions

NEW QUESTION 48
In which two states is a given session categorized as ephemeral? (Choose two.)

A TCP session waiting for FIN ACK

A UDP session with packets sent and received

A UDP session with only one packet received

A TCP session waiting for the SYN ACK

NEW QUESTION 49
What conditions are required for two FortiGate devices to form an OSPF adjacency? (Choose three.)

IP addresses are in the same subnet.

Hello and dead intervals match.

OSPF IP MTUs match.

OSPF peer IDs match.

OSPF costs match.

NEW QUESTION 50
Refer to the exhibit, which contains a TCL script configuration on FortiManager.

An administrator has configured the TCL script on FortiManager, but failed to apply any changes to the managed device after being executed.
Why did the TCL script fail to make any changes to the managed device?

Changes in an interface configuration can only be done by CLI script.

The TCL script must start with #include <>.

Incomplete commands are ignored in TCL scripts.

The TCL command run_cmd has not been created.

NEW QUESTION 51
In which two ways does FortiManager function when it is deployed as a local FDS? (Choose two.)

It provides VM license validation services.

It supports rating requests from non-FortiGate devices.

It caches available firmware updates for unmanaged devices.

It can be configured as an update server, a rating server, or both.

NEW QUESTION 52
Examine the output of the ‘get router info ospf interface’ command shown in the exhibit; then answer the question below.

Which statements are true regarding the above output? (Choose two.)

The port4 interface is connected to the OSPF backbone area.

The local FortiGate has been elected as the OSPF backup designated router.

There are at least 5 OSPF routers connected to the port4 network.

Two OSPF routers are down in the port4 network.

NEW QUESTION 53
View these partial outputs from two routing debug commands:

Which outbound interface will FortiGate use to route web traffic from internal users to the Internet?

Both port1 and port2

port3

port1

port2

NEW QUESTION 54
Examine the following partial output from a sniffer command; then answer the question below.

What is the meaning of the packets dropped counter at the end of the sniffer?

Number of packets that didn’t match the sniffer filter.

Number of total packets dropped by the FortiGate.

Number of packets that matched the sniffer filter and were dropped by the FortiGate.

Number of packets that matched the sniffer filter but could not be captured by the sniffer.

NEW QUESTION 55
View the exhibit, which contains the output of a debug command, and then answer the question below.

What statement is correct about this FortiGate?

It is currently in system conserve mode because of high CPU usage.

It is currently in FD conserve mode.

It is currently in kernel conserve mode because of high memory usage.

It is currently in system conserve mode because of high memory usage.

NEW QUESTION 56
View the exhibit, which contains a screenshot of some phase-1 settings, and then answer the question below.

The VPN is up, and DPD packets are being exchanged between both IPsec gateways; however, traffic cannot pass through the tunnel.
To diagnose, the administrator enters these CLI commands:

However, the IKE real time debug does not show any output .
Why ?

The debug output shows phases 1 and 2 negotiations only. Once the tunnel is up, it does not show any more output.

The log-filter setting was set incorrectly. The VPN’s traffic does not match this filter.

The debug shows only error messages. If there is no output, then the tunnel is operating normally.

The debug output shows phase 1 negotiation only. After that, the administrator must enable the following real time debug: diagnose debug application ipsec -1.

NEW QUESTION 57
Refer to the exhibit, which contains the partial output of the get vpn ipsec tunnel details command.

Based on the output, which two statements are correct? (Choose two.)

Phase 2 authentication is set to sha1 on both sides.

Anti-replay is disabled.

Hub2Spoke1 is a policy-based VPN.

Hub2Spoke1 is configured on interface wan2.

NEW QUESTION 58
Refer to the exhibit, which contains a TCL script configuration on FortiManager.
An administrator has configured the TCL script on FortiManager, but the TCL script failed to apply any changes to the managed device after being run.

Why did the TCL script fail to make any changes to the managed device?

The TCL command run_cmd has not been created.

The TCL script must start with tinclude <>.

Incomplete commands are ignored in TCL scripts.

Changes to an interface configuration can be made only by a CLI script.

NEW QUESTION 59
Refer to exhibit, which contains the output of a BGP debug command.

Which statement explains why the state of the 10.200.3.1 peer is Connect?

The local router is receiving BGP keepalives from the remote peer, but the local peer has not received the OpenConfirm yet.

The TCP session to 10.200.3.1 has not completed the 3-way handshake.

The local router is receiving the BGP keepalives from the peer, but it has not received a BGP prefix yet.

The local router has received the BGP prefixes from the remote peer.

NEW QUESTION 60
Two independent FortiGate HA clusters are connected to the same broadcast domain. The administrator has reported that both clusters are using the same HA virtual MAC address. This creates a duplicated MAC address problem in the network. What HA setting must be changed in one of the HA clusters to fix the problem?

Group ID.

Group name.

Session pickup.

Gratuitous ARPs.

https://help.fortinet.com/fos50hlp/54/Content/FortiOS/fortigate-high-availability-52/HA_failoverVMAC.htm

NEW QUESTION 61
View the exhibit, which contains the output of a debug command, and then answer the question below.

Which one of the following statements about this FortiGate is correct?

It is currently in system conserve mode because of high CPU usage.

It is currently in extreme conserve mode because of high memory usage.

It is currently in proxy conserve mode because of high memory usage.

It is currently in memory conserve mode because of high memory usage.

NEW QUESTION 62
An LDAP user cannot authenticate against a FortiGate device.
Examine the real time debug output shown in the exhibit when the user attempted the authentication; then answer the question below.

Based on the output in the exhibit, what can cause this authentication problem?

User student is not found in the LDAP server.

User student is using a wrong password.

The FortiGate has been configured with the wrong password for the LDAP administrator.

The FortiGate has been configured with the wrong authentication schema.

NEW QUESTION 63
Examine the following partial outputs from two routing debug commands; then answer the question below:

Why the default route using port2 is not displayed in the output of the second command?

It has a lower priority than the default route using port1.

It has a higher priority than the default route using port1.

It has a higher distance than the default route using port1.

It is disabled in the FortiGate configuration.

NEW QUESTION 64
View the exhibit, which contains the partial output of an IKE real-time debug, and then answer the question below.

Which statements about this debug output are correct? (Choose two.)