[Aug 02, 2024] 2Pass4sure LEED-Green-Associate dumps & USGBC LEED sure practice dumps [Q100-Q114]

LEED-Green-Associate USGBC

admin • August 2, 2024

[Aug 02, 2024] 2Pass4sure LEED-Green-Associate dumps & USGBC LEED sure practice dumps [Q100-Q114]

Rate this post

[Aug 02, 2024] 2Pass4sure LEED-Green-Associate dumps & USGBC LEED sure practice dumps

USGBC LEED-Green-Associate Actual Questions and Braindumps

NO.100 The intent of the location valuation factor is to incentivize the purchase of products that

reduce transportation emissions

support the local economy and workers

emit no Volatile Organic Compounds (VOCs)

comply With responsible extraction regulations

Explanation
The location valuation factor is a concept that applies to several credits under the Materials and Resources credit category in LEED v4. It means that if the purchased products or materials are extracted, manufactured, and purchased within 100 miles (160 kilometers) of the project, LEED will award the project in the credit calculations by valuing those products at 200% of their cost1. This is to incentivize the purchase of products that reduce transportation emissions and environmental impacts associated with long-distance shipping2.
References: 2 LEED v4: Building Design + Construction Guide, Materials and Resources, p. 487-4881 LEED
2009 vs. LEED v4: Regional Materials – LaForce, LLC.

NO.101 Which Of the following is an example Of Integrative process?

Judicious use of recyclable materials during construction

Rapid incorporation of design changes during construction

Ongoing evaluation of feedback mechanisms during building operation

Conscientious maintenance of building equipment during building operation

Explanation
Integrative process is a collaborative approach that involves all project stakeholders in the design and decision-making process from the beginning to the end of a project. It aims to optimize the performance, environmental, social, and economic outcomes of a project by considering the interrelationships and synergies between various building and site systems. One of the key aspects of integrative process is to establish feedback loops that allow for continuous monitoring, evaluation, and improvement of the project performance during its operation. Therefore, option C is an example of integrative process, while the other options are not directly related to it. References: Integrative process | U.S. Green Building Council, section “Integrative Process”; Understanding Integrative Design in LEED v4, page 1; LEED Integrative Process Credit Explained, section “INTEGRATIVE PROCESS V4 CREDIT OVERVIEW”

NO.102 A developer has asked the building designer to incorporate a landscape irrigation system using the building’s graywater in order to earn LEED points. Which is the most appropriate source of graywater for this use?

Urinal

Toilet

Janitor sink

Bathroom sink

Explanation
Graywater refers to wastewater that is not heavily soiled, typically from bathroom sinks, showers, tubs, and washing machines. It does not include water from toilets (which is considered blackwater) or kitchen sinks (which can contain food waste). Graywater can be treated and reused for purposes like landscape irrigation, which can save water and earn LEED points. References: LEED Green Associate Candidate Handbook, U.S.
Green Building Council resources

NO.103 In addition to the temperature and humidity, what is another factor to consider when implementing thermal comfort strategies?

Daylight

Acoustics

Air movement

Green cleaning

Explanation
Air movement is a factor that affects the thermal comfort of occupants, as it influences the heat exchange between the human body and the surrounding air1. Air movement can be controlled by mechanical systems, such as fans, or natural systems, such as operable windows2. LEED v4 requires that at least 50% of individual occupant spaces have thermal comfort controls that allow occupants to adjust air movement in their local environment3.
References: 1 LEED (BD+C)- Indoor Environmental Quality Credit: Thermal comfort2 Get to Know LEED:
How to Provide Thermal Comfort in a LEED for Homes … 3 CI-v4.1 EQc5: Thermal comfort | LEEDuser.

NO.104 Should non-design team stakeholders be included in design charrettes?

No, because it may increase legal liability

Yes, because it may help to reduce future litigation

No, because they lack the expertise to contribute design ideas

Yes, because they enhance understanding of community concerns

Design charrettes are collaborative sessions where stakeholders brainstorm and generate design solutions for a project. Non-design team stakeholders, such as community members, clients, users, and regulators, can provide valuable input and feedback on the project goals, needs, challenges, and opportunities. Including them in design charrettes can help to create more sustainable, inclusive, and responsive design outcomes that meet the expectations and requirements of all parties involved. References: LEED Green Associate Candidate Handbook, page 14; LEED Green Associate | U.S. Green Building Council, section “LEED v4 Rating Systems”

NO.105 Which is an example of a low-cost Water Efficiency strategy?

Install new flush valves or flow restrictors

Install subsurface cisterns to collect stormwater

Use only compostable toilets throughout the facility

Incorporate an on-site blackwater treatment system

Explanation
Installing new flush valves or flow restrictors is a low-cost strategy to improve water efficiency. These devices reduce the amount of water used in each flush or flow, leading to significant water savings over time. Other strategies like installing subsurface cisterns to collect stormwater, using only compostable toilets throughout the facility, or incorporating an on-site blackwater treatment system can also improve water efficiency, but they typically involve higher upfront costs. References: LEED Green Associate Candidate Handbook, U.S.
Green Building Council resources

NO.106 Which of the following is a strategy for preventing light pollution?

Install up-lighting

Install shielded fixtures

Install high performance windows

Use dark paving materials to diminish light distribution

NO.107 Which of the following strategies, when designed together, can save energy and improve occupant experience?

Daylighting and natural ventilation

Thermal comfort and water meters

Energy metering and thermal comfort

Ventilation and carbon monoxide monitoring

NO.108 Which of the following is a prerequisite in LEED v4 Water Efficiency category?

Rainwater Management

Cooling Tower Water Use

Building-Level Water Metering

Building-Level Energy Metering

Explanation
Building-Level Water Metering is a prerequisite in LEED v4 Water Efficiency category. Building-Level Water Metering means that the project must install permanent water meters that measure the total potable water use for the building and associated grounds. The project must also commit to sharing the water usage data with USGBC for at least five years after occupancy or certification. The LEED Green Associate Candidate Handbook states that this is one of the two prerequisites in the Water Efficiency category [1, p.
14]. References: [LEED Green Associate Candidate Handbook], [Building-Level Water Metering | U.S. Green Building Council]

NO.109 The Montreal Protocol banned the production of

freon

CFCs

HCFCs

ammonia

Explanation
The Montreal Protocol is an international treaty that aims to protect the ozone layer by phasing out the production and consumption of ozone-depleting substances (ODS). ODS are chemicals that contain chlorine or bromine, which can destroy the ozone molecules in the stratosphere. CFCs, or chlorofluorocarbons, are a group of ODS that were widely used in refrigeration, air conditioning, aerosols, and solvents. The Montreal Protocol banned the production of CFCs in 201012. Freon is a trade name for some CFCs and HCFCs, or hydrochlorofluorocarbons, which are also ODS but less harmful than CFCs. The Montreal Protocol also controls the production of HCFCs, which are being phased out gradually12. Ammonia is not an ODS and is not regulated by the Montreal Protocol1.
References:
The Montreal Protocol on Substances That Deplete the Ozone Layer | U.S. Department of State2 Montreal Protocol – Wikipedia1 The Montreal Protocol: fixing the ozone layer and taking climate action – Canada.ca3

NO.110 Which Is a component of a construction waste management plan?

List of materials to be diverted from disposal

Projected cost savings from diverting waste

Quantity of waste generated from excavated soil

Distance of the recycling facility from the project site

Explanation
A list of materials to be diverted from disposal is a component of a construction waste management plan. A construction waste management plan is a document that outlines the goals, procedures, and responsibilities for diverting construction and demolition waste from landfills or incinerators. A list of materials to be diverted from disposal identifies the types and quantities of materials that can be recycled, reused, salvaged, or donated, as well as the destinations and methods for diversion. The other options are not components of a construction waste management plan. Projected cost savings from diverting waste is a potential benefit of implementing a construction waste management plan, but it is not a required component. Quantity of waste generated from excavated soil is a factor that affects the construction waste generation rate, but it is not a component of a construction waste management plan. Distance of the recycling facility from the project site is a factor that affects the transportation emissions and costs associated with diverting waste, but it is not acomponent of a construction waste management plan. References: LEED Green Associate Candidate Handbook, page 28; USGBC, [Materials and Resources], page 3.

NO.111 During which stage of a project is implementation of the Integrative Process most effective in improving performance?

Operation

Early de sign

Construction

Construction document

Explanation
The Integrative Process is most effective during the early design stage of a project. This is when key decisions about the project are being made that can have a significant impact on its sustainability performance. By considering sustainability objectives from the outset, teams can identify opportunities for synergies and cost savings that may not be apparent later in the project. References: LEED Green Associate Candidate Handbook, U.S. Green Building Council resources

NO.112 Which type of site Is appropriate for development of LEED projects?

Floodplain

Greenfield

Brownfield

Undeveloped

A brownfield site is appropriate for development of LEED projects because it is a site that has been previously used for industrial or commercial purposes and may be contaminated by pollutants or hazardous substances. Developing a brownfield site can help reduce environmental impacts, such as soil erosion, habitat loss, and water consumption, by reusing existing infrastructure and restoring degraded land. LEED projects can earn credits for developing on brownfield sites under the Sustainable Sites category. Reference: LEED v4 BD+C Reference Guide, Sustainable Sites, page 35; Best Management Practice #14: Alternative Water Sources1

NO.113 Select the type of approach that promotes the conservation of materials and resources by linking elements in order to form relationships with their function

Open Flow

Closed Flow

Open Systems

Closed Systems

A closed system is a type of approach that promotes the conservation of materials and resources by linking elements in order to form relationships with their function1. A closed system is one that does not exchange matter or energy with its surroundings, and therefore minimizes waste and maximizes efficiency2. A closed system aims to achieve a circular economy, where resources are reused, recycled, or recovered, rather than disposed of3. A closed system can also enhance resource productivity, reduce environmental impacts, and foster innovation4.
Reference:
Zero Waste Definition
Closed system | physics
Material Resources, Productivity and the Environment
Sustainable Materials Management: The Road Ahead

NO.114 Which permanently installed building products are addressed in the Materials and Resources Credit category calculation?

Framing

Elevators

Process equipment

Formwork for concrete

Explanation
The Materials and Resources Credit category calculation addresses the permanently installed building products that are part of the building’s structure, enclosure, and interior elements. These include framing, flooring, insulation, windows, doors, interior walls, ceilings, and finishes. Process equipment, elevators, furniture, and formwork for concrete are not included in the calculation . References: LEED v4 Green Associate Candidate Handbook, LEED v4 BD+C Reference Guide

Loading …