Q94. Refer to the exhibit.

Refer to the exhibit. An engineer must configure FCoE between the N9K-A switch and the FCF-A Nexus 9000 core switch. The deployment has these characteristics:
The N9K-Aand N9K-B top-of-rack switches share the domain ID of the core switches.
The hosts are equipped with converged network adapters.
The only VSAN that is permitted to traverse port-channel 100 is VSAN 20.
Which configuration completes the FCoE configuration on the N9K-A device?

Q95. Drag and drop the storage technologies from the left onto the correct descriptions on the right.

Q96. An engineer must shut down the Ethernet 1/2 interface when the Ethernet 4/5 interface state is down. Drag and drop the CLI commands from the bottom onto the blanks in the exhibit to implement this EEM. Not all commands are used.

Q97. Refer to the exhibit.

In a bidirectional PIM network using Phantom RP as an RP redundancy mechanism, two Cisco NX-OS routers have these requirements:
* R1 must be the active RP.
* R2 must be the backup RP that is used only if R1 is not reachable
Drag and drop the configuration steps to complete the configuration for Router 2. Not all configuration steps are used.

Q98. What is an advantage of NFSv4 over Fibre Channel protocol?

Q99. An engineer changed a configuration and must perform a rollback. Which statement applies to a Cisco Nexus 5600 Series switch?

Q100. A storage array must be connected to port ethernet1/10 on a Cisco MDS 9000 Series Switch.
In addition, the array must connect using the FCoE protocol and be single-homed.
Which configuration meets these requirements?

Q101. A network engineer must implement RBAC on Cisco MDS 9000 Series Multilayer Switches.
Drag and drop the Cisco MDS 9000 Series roles from the left onto the correct categories on the right.

Q102. An engineer must migrate a Cisco UCS C-Series server from Cisco SingleConnect to direct connect integration mode. The Cisco UCS Manager Rack Server Discovery Policy and Rack Management Connection Policy are set to Immediate and Auto-Acknowledge. Which set of steps accomplishes this task?

Q103. Refer to the exhibit.

What is the result of this series of commands?

Q104. Which value is missing in the field in the key called “msg” in this JSON response?
Request:

Response:

Q105. The Cisco Nexus 5600 Series Switch experiences occasional packet drops on interface ethernet
1/16. An engineer wants to implement a SPAN session to investigate the issue further. The network analyzer to which the packets must be directed is located on interface 1/3. The analyzer is limited on disk space available for traffic capture, so the Nexus switch should send only the relevant data.
Which two command sets configure the SPAN session that meets these requirements? (Choose two.)

Q106. Refer to the exhibit.

What is the outcome of this command when the ELPD is updated on a Cisco Nexus 9000 series switch?

Q107. What is an advantage of NFS as compared to Fibre Channel?

Q108. A network engineer must configure FCoE on an interface of a Cisco MDS 9000 Series Switch. It should be used for mapping between VLAN 600 and VSAN 6. Drag and drop the commands from the bottom into their implementation order in the FCoE configuration. Not all commands are used.

Q109. A Cisco MDS 9000 Series Switch is configured for SAN Analytics and SAN Telemetry Streaming. An engineer must enable analytics for NVMe on interfaces in the range of fc1/1-12. Due to a large amount of traffic generated in the SAN environment, the data must be collected at regular intervals of 60 seconds from ports fc 1-12 and then for ports fc13-24 for the next 60 seconds. Ports in the range fc4/13-14 were already enabled for analytics. Which set of commands must be used to meet these requirements?

Q110. An engineer must remove the running configuration of a Cisco Nexus 9000 Series Switch and replace it with a backup file without restarting the switch. The backup file is stored on an SFTP server that is reachable via the An engineer must remove the running configuration mgmt0 interface Which set of commands accomplishes this task’

Q111. Refer to the exhibit.

What be connected to clear the HA NOT READY status?

Q112. An engineer needs to make an XML backup of Cisco UCS Manager The backup should be transferred using an authenticated and encrypted tunnel and it should contain all system and service profiles configuration Which command must be implemented to meet these requirements?

Q113. Refer to the exhibit.

Refer to the exhibit A network engineer created a new role to be assigned to the SAN users The requirement is for users to have these characteristics permitted to show access to the system, SNMP, module, and hardware information permitted to run debug zone and exec fcping commands