Rate this post

100% Reliable Microsoft FlashArray-Implementation-Specialist Exam Dumps Test Pdf Exam Material

Based on Official Syllabus Topics of Actual Pure Storage FlashArray-Implementation-Specialist Exam

Pure Storage FlashArray-Implementation-Specialist Exam Syllabus Topics:

Topic Details
Topic 1
  • Post-Installation
  • Upgrade: This section of the exam measures the skills of FlashArray Implementation Specialists and evaluates how professionals confirm system functionality after installation or an upgrade. It involves validating connectivity, running health checks, confirming configurations, and ensuring that the deployment meets operational expectations.
Topic 2
  • Installation: This section of the exam measures the skills of Enterprise Infrastructure Technicians and focuses on executing a successful installation of FlashArray systems. It tests the ability to perform physical setup, cabling, configuration of network settings, and the application of initial system configurations necessary for full deployment.
Topic 3
  • Pre-Installation
  • Upgrade: This section of the exam measures the skills of Enterprise Infrastructure Technicians and covers all preparation activities before deploying or upgrading a Pure Storage FlashArray. It includes understanding environmental requirements, verifying prerequisites, checking compatibility, and validating system readiness through appropriate tools and documentation.
Topic 4
  • Upgrades: This section of the exam measures the skills of FlashArray Implementation Specialists and focuses on tasks involved in managing firmware and software upgrades. Candidates must demonstrate knowledge of upgrade planning, verification steps, and rollback procedures, ensuring that systems are updated with minimal disruption to service.

 

NEW QUESTION 22
A customer has purchased a DirectFlash Shelf, but lacks available space in the same rack as the chassis. There is available space in a rack 6m away. What step should be taken prior to implementation?

 
 
 

NEW QUESTION 23
If drives need to be relocated within an array for an XFORM upgrade, when should this be completed?

 
 
 

NEW QUESTION 24
A customer has filled out the Installation Workbook. The management IP information netmask is specified as “255.255.255.223” and the gateway is specified as “10.24.18.1”. What corrective action should be taken to reconcile the IP configuration?

 
 
 

NEW QUESTION 25
When performing an install on a FlashArray, what step should be taken first?

 
 
 

NEW QUESTION 26
An Implementation Engineer performs a controller upgrade. What is the command to check I/O health?

 
 
 

NEW QUESTION 27
Before leaving the site after an install, who is required to provide completion sign-off?

 
 
 

NEW QUESTION 28
Which PCIe slot supports 4-port FC cards on FlashArray//XL?

 
 
 

NEW QUESTION 29
At the completion of an upgrade, which command is used to send phonehome logs?

 
 
 

NEW QUESTION 30
Which default speed FC SFPs are shipped in FlashArray//XCR4 FC arrays?

 
 
 

NEW QUESTION 31
A customer has ordered several FlashArrays and wants to have ActiveCluster configured. What is the maximum quantity of arrays supported with ActiveCluster?

 
 
 

NEW QUESTION 32
An Implementation Engineer is performing a capacity consolidation on an X50R3.
Which command is needed for the engineer to determine whether the customer’s FlashArray supports SAS Flash Modules?

 
 
 

NEW QUESTION 33
What is the rack unit height of a FlashArray//XL?

 
 
 

NEW QUESTION 34
What should an Implementation Engineer do when installing rails in a threaded-hole rack?

 
 
 

NEW QUESTION 35
After upgrading Purity during a new installation, which command should an Implementation Engineer run to determine what version of Purity will be loaded at the next boot of the FlashArray?

 
 
 

NEW QUESTION 36
Support requests a powercycle on a newly-installed FlashArray. What is the correct way to perform this action?

 
 
 

NEW QUESTION 37
After an Implementation Engineer installs a new FlashArray and runs health checks, they see that Phonehome and Remote Assist are NOT working correctly.
Which outbound port needs to be open for all management ports (physical and virtual)?

 
 
 

NEW QUESTION 38
A customer has purchased a FlashArray//XL. What power cables are required in order to connect this array to rack PDUs?

 
 
 

NEW QUESTION 39
What command can be used to identify interface status?

 
 
 

Free FlashArray-Implementation-Specialist Dumps are Available for Instant Access: https://www.2pass4sure.com/Pure-Storage-FAIS/FlashArray-Implementation-Specialist-actual-exam-braindumps.html

         

Related Links: myportal.utt.edu.tt myportal.utt.edu.tt myportal.utt.edu.tt myportal.utt.edu.tt myportal.utt.edu.tt myportal.utt.edu.tt